# Vaporesso Luxe XR Max 2: getting started right > Unboxing the Vaporesso Luxe XR Max 2, priming the right pod, setting the power and the airflow: every move of the first day, taken in the correct order. Two pods, a coil already fitted, a screen and an airflow ring: the box holds more choices than it looks like it does, and half the disappointment people report on day one comes from a rushed priming or a pod picked at random. Getting the **Luxe XR Max 2** running takes about twenty minutes, most of which is spent waiting rather than doing anything. Here is the exact order of the moves, from opening the box to the setting you will keep. ## Starting the Luxe XR Max 2 in six steps Vaporesso quotes an internal 3200 mAh battery for this one, adjustable power up to 80 W, and two separate pods in the box. British versions ship in the 2 ml configuration the rules require here. Setting it up always follows this sequence. 1. Charge the battery fully before any use at all, over the USB-C port. 2. Choose the pod that matches the draw you want, direct or mouth to lung, from the two supplied. 3. Prime the coil by putting e-liquid straight onto the cotton ports. 4. Fill the pod, then stand it upright and leave it for ten minutes. 5. Clip the pod in, wake the device with five clicks, and set the power inside the range printed on the coil. 6. Adjust the airflow after a few draws, never before. Skipping step three or step four leads to the same place: a burnt taste on the first puff and a brand new coil straight in the bin. ## Understanding the two pod system This is what sets the kit apart, and it changes how you use it day to day. Vaporesso does not supply two coils to swap inside one reservoir, but two complete and separate pods. The direct lung pod arrives preinstalled with a low resistance GTX mesh coil. The draw is airy, suited to inhaling straight to the lungs, with high liquid consumption and a lot of vapour for the effort. The mouth to lung pod comes packed separately in the box with its own coil, and aims at a tight indirect draw instead. Consumption falls away sharply and the flavour gathers in rather than spreading out. Because each pod carries its own reservoir, you can keep two different e-liquids running in parallel and switch between them in seconds without rinsing anything. That is the most useful thing about the kit and the one least often mentioned: a dessert on a tight draw during the day, a fruit on an airy one in the evening, with no crossover of taste at all. ## Priming the coil properly Priming is the only irreversible move of the whole setup. A coil fired dry is finished for good, and that includes the one that arrives already fitted in the pod. Take the coil out of the pod and find the ports on its side, the openings through which the cotton is visible. Put three to five drops of e-liquid onto each one, until the white of the cotton turns translucent right across the opening. Put the coil back, fill the pod through the silicone side flap, then stand the assembly upright for ten minutes. That pause lets the cotton draw liquid through its whole thickness rather than just wetting the surface where the drops landed. Finish with a few draws taken without firing the device, mouth on the drip tip. That pulls liquid towards the cotton and completes the priming without heating anything. ## Setting the power on the Luxe XR Max 2 The screen reports the wattage and the resistance of the coil as soon as the pod goes in. The setting is made before the first puff rather than corrected afterwards. Work from the range printed on the side of the coil and start at the bottom of it. That range is the manufacturer figure, it is specific to the coil in your hand, and no article can give you a better one. Take three or four short draws there, then climb in small increments until you find the rendering you want. Coming up gradually spreads the liquid evenly and keeps hot spots off the mesh, which is exactly what a fresh coil needs on its first tankful. A result that comes across hot means the wattage has gone past what the liquid in use can carry. A flat, cool result means the opposite. Heavily flavoured liquids generally settle towards the lower part of the printed range rather than the top. ## Getting the airflow right at the right moment The airflow ring changes how much air is drawn in, which changes both the temperature and the density of the vapour. It is set after the power, never at the same time. Open it fully first, take two draws, then close it progressively until you feel resistance building against the draw. Each notch closed concentrates the flavour and warms the result. Changing the airflow and the power together makes it impossible to tell which one caused what. That is the most common setup mistake on a versatile pod kit, and it costs a quarter of an hour every time a new pod goes in. ## Charging and looking after the battery The 3200 mAh cell is built in and cannot be replaced, which makes charging habits decisive for how long the whole device stays useful. Recharge as soon as the screen reports a low level rather than waiting for it to shut down. Repeated deep discharges on an integrated cell are paid for in runtime within a few months, and nothing you can do afterwards brings it back. Use a modest mains adapter rather than a fast phone charger. The time saved on this capacity is small, while the extra heat measurably accelerates ageing. For anyone who also runs removable cells, the same logic is set out in our tutorial on the [vape battery charger](/uk/vape-battery-charger/). If the device is going unused for a while, leave it around half charge rather than full or flat, and take the pod out so liquid is not sitting against the coil. ## Everyday upkeep The kit asks for very little attention, but three habits noticeably extend how long each pod lasts before it needs replacing. - Wipe the pod bay with kitchen roll every two or three refills, so condensation never reaches the gold contacts. - Close the fill flap fully, checking that the silicone bung is seated flat rather than resting on the lip. - Store the device upright, never lying in a bag, to limit liquid creeping up the central chimney. The priming and coil changing logic is the same across every device with cotton built in, brand regardless. It is covered in detail in our tutorial on [Geekvape coils](/uk/geekvape-coils/), and the rest of the [hands-on section](/uk/category/hands-on/) applies it to other kits. ## FAQ These come up regularly in the first few weeks with the kit, around pods, charging and small incidents. ### How long does a pod last? That depends on the liquid and the wattage in use, with no universal marker. Change it as soon as the flavour flattens or a harsh note appears at the end of a draw. ### Do pods from the earlier Luxe XR fit? Retailers list pods from the series as compatible across several kits in the range. Check the exact reference on the box before ordering, since the formats have moved on between generations. ### Can it be used while charging? The USB-C port allows charging, but vaping at the same time makes the cell and the circuit work together. Waiting for the cycle to finish is better, and it is quick enough that little is lost. ### What if the screen reports a coil error? Take the pod out, wipe the gold contacts on the pod and in the bay with a dry cloth, then reinsert it. A trace of condensation between the two is enough to interrupt detection. ### Can liquid come up into the drip tip? It happens after the device has travelled lying down, or after a pressure change on a flight. Draw without firing, drip tip against kitchen roll, to clear the excess before carrying on. ## Getting the most out of a Luxe XR Max 2 A good start comes down to three things: patient priming, a gradual climb in power inside the printed range, and an airflow adjustment made on its own. Run with both pods in parallel, the **Luxe XR Max 2** covers two very different styles of vaping from one device in a pocket. Give the first day the time it asks for and the hardware then lets itself be forgotten for weeks at a stretch. The same method transfers to most versatile pod kits sold in Britain, whatever name is on the box. Editorial content for adult readers only. Vaping products usually contain nicotine, a substance that causes addiction. Not for sale to under-18s in the United Kingdom. This article is not a buying recommendation.